40 ft module
RECOVER 40
The full recovery environment.
The recovery flagship.
RECOVER 40 carries everything in RECOVER 20 — freestanding cold plunge, sauna, steam and red light — and adds a dedicated stretch, yoga and mobility area.
The difference is room to actually move between modalities instead of stepping around them. Heat, cold, light and floor work in one sequence, without the squeeze.
Room between them
Sauna and steam along one side, freestanding plunge clear of the walkway, open floor beyond.
Floor work included
A dedicated stretch, yoga and mobility area — mats down, nothing to move first.
It moves
Set on a prepared pad, not a permanent foundation.
Cold plunges are freestanding, above-deck units. Homebase does not build in-ground, recessed or sunken tubs.
Dimensions
40 ft high-cube module
- Exterior L × W × H
- 40 ft × 8 ft × 9 ft 6 in
- Exterior footprint
- 320 sq ft
- Interior before finish
- 39 ft 5 in × 7 ft 8 in × 8 ft 10 in
- Interior finished (approx.)
- 39 ft × 7 ft × 8 ft 2 in
- Finished interior area (approx.)
- 273 sq ft
Finished interior dimensions are approximate and vary with the wall assembly.
Concept imagery. Renderings of Homebase builds, not photographs of delivered projects.
Standard equipment
- Cold plunge (freestanding)
- Sauna
- Steam
- Red light
- Dedicated stretch / yoga / mobility area
What it’s built for
- The full four modalities plus a dedicated stretch, yoga and mobility area.
- Several people using the environment at the same time.
- Floor work in the same space as heat and cold, with mats already down.
Standard
- Cold plunge (freestanding)Recovery
- SaunaRecovery
- SteamRecovery
- Red lightRecovery
- Stretch / yoga / mobility areaRecovery
- Cedar interiorFinish
Configurable
- Hot tub + cold plunge — Cottonwood by Hydro System (exterior deck)Site
- Hyperbaric chamber (upgrade)Recovery
- ShowerRecovery
- Exterior deck integrationSite
Specified equipment
One unit. A hot side and a cold side, steps from the door.
Hot tub + cold plunge: Cottonwood by Hydro System.
Hydro System is our supplier partner for the hot tub and cold plunge. The Cottonwood is a single acrylic unit with two sides: one warms to 104°F, the other holds as low as 37°F.
Hot, then cold, then back inside to the sauna. No second appointment, no drive, no shared locker room.
Exterior deck placement. The Cottonwood is 91 in wide and a finished module interior is approximately 84 in, so it sits on the deck — freestanding and above deck, never recessed or sunken. Sauna and steam live inside the module; hot and cold live on the deck.
- 205 gallons of water is significant weight before the unit and its occupants. The deck and its footings are designed to carry the filled unit, engineered for the specific installation.
- Exterior placement means freeze protection, drainage and service access are part of the design, confirmed per project.
- Electrical, plumbing and installation requirements are confirmed with the manufacturer during design.
Hydro System is a supply partner. Specifications are the manufacturer's published figures and are confirmed at design.
Specification
- Dimensions
- 91 × 91 × 36 in
- Capacity
- 205 gallons
- Material
- Acrylic
- Hot side
- Warms to 104°F
- Cold side
- As low as 37°F
- Jets
- 25
- Cabinet
- Chestnut · Driftwood · Graphite
- Acrylic
- Midnight Canyon · Smoky Mountain · Sterling · Storm Cloud
Concept imagery. Renderings of Homebase builds, not photographs of delivered projects.
Available upgrade
Hyperbaric chamber
An available equipment upgrade on RECOVER 20 and RECOVER 40.
A hyperbaric chamber is a large, heavy piece of equipment. Accommodating one changes the build: floor area, structural loading, clearance around the unit, door and access dimensions to get it in, dedicated electrical service, and ventilation.
It is a premium upgrade and it increases project investment. What that means for your build is quantified at your design consultation.
Chamber selection, siting and installation are specified with the manufacturer for each project.
Investment direction is shared at your design consultation.
What the build has to accommodate
- Dedicated floor area and clearance around the unit
- Structural loading confirmed for the specified unit
- Access route and door dimensions for installation
- Dedicated electrical service
- Ventilation and clearances per the manufacturer
Best for
- Recovery as the main event
- More than one person using it
- Stretch and mobility work at home
Site considerations
- Water supply and drainage
- Power service
- 40 ft delivery access
- Deck and footings engineered to carry a filled hot tub or plunge
- Freeze protection, drainage and service access for exterior units
Investment direction is shared at your design consultation.
Moveability
Build it here. Take it with you.
A Homebase sits on a prepared pad, not a foundation you are married to.
An addition stays with the house. A Homebase does not have to.
It is a manufactured structure, set down rather than built in place. Power is connected, water and drainage where recovery is included, and the module is levelled on the pad. All of that can be undone.
A sealed, coated shell is also part of why a Homebase can be relocated rather than demolished. The structure that gets lifted off the pad is the same steel box we sealed in the shop.
Can you move it? →Relocation is real, not automatic. It depends on access for a crane and transport, the pad at the new property, the utility runs at both ends, and what has been built around the module since it was set. We assess each site rather than promise every one.
Concept imagery. Renderings of Homebase builds, not photographs of delivered projects.
